Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Flow fundamentals

Measure flow. Understand the conditions.

Flow rate calculator

Calculate volume rates, pipe flow, pressure relationships and unit conversions. Start with a measured volume and time below, or explore 123 focused calculators with worked tables and published references.

Your flow inputs

L
s

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

Choose your calculation

All flow calculators

Liquids, gases, channels, equipment and unit conversions.

Flow fundamentals

Flow Rate CalculatorPipe Flow Rate CalculatorFlow Velocity CalculatorPipe Diameter from Flow CalculatorRectangular Duct Flow CalculatorDuct Area from Airflow CalculatorMass Flow Rate CalculatorVolume Flow from Mass Flow CalculatorDensity from Flow Rates CalculatorTank Filling Time CalculatorDraining Tank Orifice CalculatorMass & Volume Flow Converter

Pipe hydraulics

Reynolds Number CalculatorDarcy–Weisbach Head Loss CalculatorPressure to Flow Rate CalculatorPipe Friction Factor CalculatorHazen–Williams Flow CalculatorHazen–Williams Head Loss CalculatorHagen–Poiseuille Flow CalculatorPipe Fitting Minor Loss CalculatorEquivalent Pipe Length CalculatorPressure & Head CalculatorBernoulli Equation Calculator

Valves & flow measurement

Liquid Orifice Flow CalculatorOrifice Diameter from Flow CalculatorVenturi Flow Meter CalculatorValve Cv Flow CalculatorRequired Valve Cv CalculatorValve Kv Flow CalculatorDifferential Pressure Flow CalculatorFlow Meter Pulse CalculatorNozzle K-Factor Flow Calculator

Pumps & water systems

Pump Power CalculatorPump Flow from Power CalculatorPump Affinity Laws CalculatorDisplacement Pump Flow CalculatorPool Turnover Flow CalculatorWell Recovery Rate CalculatorRepeated Bucket Flow Test CalculatorHydrant Residual Pressure Flow CalculatorHydrant Pitot Discharge Calculator

Open channels & drainage

Rectangular Channel Flow CalculatorTrapezoidal Channel Flow CalculatorPartially Full Pipe Flow CalculatorNormal Depth CalculatorFroude Number CalculatorRectangular Critical Depth CalculatorRectangular Weir Flow CalculatorV-Notch Weir Flow CalculatorBroad-Crested Weir CalculatorRational Method Runoff CalculatorDarcy Groundwater Flow CalculatorConfined Aquifer Radial Flow Calculator

Gas & compressed air

ACFM to SCFM CalculatorSCFM to ACFM CalculatorGas Density CalculatorCompressible Gas Nozzle CalculatorWet to Dry Standard Gas Flow CalculatorGas Cylinder Duration CalculatorPneumatic Cylinder Air Consumption Calculator

Airflow & ventilation

Airflow CFM CalculatorAir Changes to CFM CalculatorBathroom Exhaust Fan Flow CalculatorFan Power CalculatorFan Flow from Power CalculatorFan Affinity Laws CalculatorCompressor Receiver Fill Time CalculatorSensible Heat Airflow CalculatorHood Face Velocity Airflow Calculator

Heat & industrial applications

Heating & Chilled Water Flow CalculatorWater Flow Heat Transfer CalculatorSteam Mass Flow from Heat Duty CalculatorCounterflow Heat Exchanger LMTD CalculatorCarburetor CFM CalculatorFuel Injector Pressure Flow CalculatorFuel Flow from Horsepower CalculatorChromatography Linear Flow Calculator3D Printer Volumetric Flow CalculatorChemical Dosing Flow CalculatorHydraulic Residence Time Calculator

Infusion & breathing arithmetic

IV Flow Rate Arithmetic CalculatorIV Drops per Minute Arithmetic CalculatorInfusion Duration Arithmetic CalculatorInfusion Concentration Arithmetic CalculatorPeak Flow Personal-Best Percentage CalculatorPeak Flow Daily Variability Arithmetic

Flow unit conversions

US GPM to US GPH ConverterUS GPH to L/h ConverterUS GPM to L/min ConverterUS GPM to L/s ConverterUS GPM to m³/h ConverterUS GPM to CFS ConverterUS GPM to US MGD ConverterUS GPD to US GPM ConverterCFM to m³/h ConverterCFM to L/s ConverterCFM to CFS ConverterCFM to m³/s ConverterCFH to CFM ConverterL/min to m³/s ConverterL/min to L/s ConverterL/h to L/min Converterm³/h to m³/s Converterm³/h to L/s Converterm³/min to m³/h Converterm³/day to m³/h ConverterCFS to m³/s Converterpetroleum bbl/day to US GPM Converterpetroleum bbl/h to US GPM Converterpetroleum bbl/min to US GPM ConverterUS GPM to Imperial GPM ConvertermL/min to L/min ConvertermL/h to mL/min Converterkg/s to kg/h Converterkg/h to lb/h Converterlb/min to kg/h ConverterVolumetric Flow Unit Converter

Gas reference-unit conversions

SCFM to standard L/min ConverterSCFM to standard cm³/min ConverterSCFM to SCFH ConverterMMscf/day to SCFM Converterreference m³/h to SCFM Converterstandard cm³/min to standard L/min Converter

The method

Formula and calculation steps

Q = collected volume ÷ elapsed time.

Calculate average volumetric flow from a measured volume and elapsed time, with metric and US customary readouts.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This does not infer pressure, pump capacity or an instantaneous peak from a single collection.

Flow Rate calculation: inputs and interpretation

A timed collection measures an average over the observation interval. Ten litres collected in twenty seconds is 0.5 L/s or 30 L/min. Use a calibrated container, account for splashing and make the start/stop timing consistent. For unstable flow, a longer representative interval or repeated collections can reduce the influence of a short fluctuation.

Keep the same time basis when comparing readings. A volume total, an average rate and an instantaneous meter value answer different questions. Use the actual wetted section or measured fluid quantity rather than an outside pipe dimension or an equipment nameplate that does not describe the operating condition.

Check the numbers

Flow Rate Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Collected volume = 10 L; Collection time = 20 s.

OutputComputed result
Measured average flow30 L/min
Collected amount10 L
Observation duration20 s
Volume flow SI0.0005 m³/s
Volume flow hourly1.8 m³/h
US liquid flow7.925162 US GPM
Cubic feet per minute1.05944 CFM

How one input changes the answer

ScenarioChanged inputResult
2.5 LCollected volume7.5 L/min
5 LCollected volume15 L/min
7.5 LCollected volume22.5 L/min
10 LCollected volume30 L/min
15 LCollected volume45 L/min
20 LCollected volume60 L/min
30 LCollected volume90 L/min

Unchanged inputs use: Collected volume = 10 L; Collection time = 20 s. Results retain the model limitations described above.

Common questions

How do I calculate water flow rate?

Divide the collected volume by elapsed time, then convert the volume and time units consistently. The same arithmetic works for any measured liquid volume.

Does a 3 GPM pump always deliver 3 GPM?

No. Its actual flow depends on the pump curve and system conditions. A collection test measures the operating point at the time of the test.

Can I calculate flow from pressure alone?

No. Geometry, flow resistance and a suitable model or calibrated coefficient are also required.

Can I use this for a faucet, hose or well pump?

Yes for timed collection at the measurement location. The result does not establish a sustainable well yield or a plumbing design limit.

What is the volumetric flow rate equation in fluid mechanics?

The average volume/time equation is Q = V/t. The equivalent section equation Q = A times mean velocity requires the area and a representative average velocity. Neither equation determines pump flow from its horsepower alone.

How do I calculate gallons per minute water flow rate?

Measure a volume and its collection time. For a US gallon measurement, GPM equals gallons divided by minutes, or gallons times 60 divided by seconds. This form accepts litres and seconds and also reports US GPM.

How do I calculate mL per hour or litres per second?

Use volume divided by elapsed time with matching units. One litre per second equals 60 litres per minute or 3,600,000 mL per hour. A collected total is not itself a flow rate.

Can a flow meter calculation use a totalizer reading?

Subtract the starting total from the ending total and divide by the measured interval. Confirm totalizer units and rollover behavior. This is an interval average, not the instantaneous meter signal.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html
  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9