Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Gas & compressed air

Measure flow. Understand the conditions.

Pneumatic Cylinder Air Consumption Calculator

Estimate ideal double-acting cylinder reference-air demand for complete extend/retract cycles.

Your flow inputs

mm
mm
mm
cycles/min
kPa abs
kPa abs

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Reference L/min = (bore area + annular area) × stroke × cycles/min × actual/reference pressure, with compatible isothermal ideal-gas assumptions.

Estimate ideal double-acting cylinder reference-air demand for complete extend/retract cycles.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Not a compressor selection, actuator-force rating or validated dynamic consumption test.

Pneumatic Cylinder Air Consumption calculation: inputs and interpretation

One complete cycle includes extension and retraction. The rod reduces the retraction-side swept volume. The isothermal pressure correction assumes the same temperature and ideal-gas basis on both sides; leakage, tubing dead volume, cushions and valve behavior are not included.

Always distinguish absolute pressure from gauge pressure and absolute temperature from Celsius. Standard and normal volume rates require a stated reference condition. Real-gas properties, moisture and two-phase behavior are included only where explicitly described in the model.

Check the numbers

Pneumatic Cylinder Air Consumption Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Cylinder bore = 50 mm; Rod diameter = 20 mm; One-way stroke length = 100 mm; Complete extend/retract cycles = 30 cycles/min; Cylinder absolute pressure = 700 kPa abs; Reference absolute pressure = 101.325 kPa abs.

OutputComputed result
Ideal cylinder swept-volume air demand74.877338 reference L/min
Reference CFM2.644268 reference CFM

How one input changes the answer

ScenarioChanged inputResult
7.5 cycles/minComplete extend/retract cycles18.719334 reference L/min
15 cycles/minComplete extend/retract cycles37.438669 reference L/min
22.5 cycles/minComplete extend/retract cycles56.158003 reference L/min
30 cycles/minComplete extend/retract cycles74.877338 reference L/min
45 cycles/minComplete extend/retract cycles112.316007 reference L/min
60 cycles/minComplete extend/retract cycles149.754676 reference L/min
90 cycles/minComplete extend/retract cycles224.632014 reference L/min

Unchanged inputs use: Cylinder bore = 50 mm; Rod diameter = 20 mm; One-way stroke length = 100 mm; Complete extend/retract cycles = 30 cycles/min; Cylinder absolute pressure = 700 kPa abs; Reference absolute pressure = 101.325 kPa abs. Results retain the model limitations described above.

Common questions

Can I enter strokes per minute as cycles per minute?

Only if the count represents a full extension plus retraction. Otherwise convert the motion convention consistently.

Why does rod diameter matter?

It reduces the annular swept area on the rod side during retraction.

Can I enter gauge pressure?

No. The pressure ratio must use absolute pressure.

Does it include leaks and connected line volume?

No. The ideal swept-volume estimate excludes those additional demands.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html
  • US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html