Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Pumps & water systems

Measure flow. Understand the conditions.

Pump Power Calculator

Estimate hydraulic and input power for a specified liquid flow and differential head.

Your flow inputs

L/min
m
kg/m³
%

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Hydraulic W = density × g × Q × head; input W = hydraulic W / efficiency.

Estimate hydraulic and input power for a specified liquid flow and differential head.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Does not select a pump curve, motor, NPSH margin or electrical supply.

Pump Power calculation: inputs and interpretation

Head must describe the pump’s energy increase at the operating flow, including the system components appropriate to the chosen boundary. The efficiency input must match whether the requested input is shaft power or complete electrical input; do not mix pump-only efficiency with a wall-power claim.

A pump operates where its curve meets the system curve. The tools here isolate a stated energy, displacement or test relationship; they do not automatically select a pump or verify suction conditions, cavitation margin, protection or installation requirements.

Check the numbers

Pump Power Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Volumetric flow = 60 L/min; Pump differential head = 20 m; Fluid density = 998 kg/m³; Hydraulic-to-input efficiency = 70 %.

OutputComputed result
Pump input at chosen efficiency boundary0.27963 kW
Hydraulic power195.740734 W
Mechanical horsepower equivalent0.374989 HP

How one input changes the answer

ScenarioChanged inputResult
15 L/minVolumetric flow0.069907 kW
30 L/minVolumetric flow0.139815 kW
45 L/minVolumetric flow0.209722 kW
60 L/minVolumetric flow0.27963 kW
90 L/minVolumetric flow0.419444 kW
120 L/minVolumetric flow0.559259 kW
180 L/minVolumetric flow0.838889 kW

Unchanged inputs use: Volumetric flow = 60 L/min; Pump differential head = 20 m; Fluid density = 998 kg/m³; Hydraulic-to-input efficiency = 70 %. Results retain the model limitations described above.

Common questions

How do I calculate pump horsepower?

Calculate input watts under the chosen efficiency basis, then divide by mechanical horsepower watts; a readout is included.

Can pressure replace head?

Convert a consistent pressure difference to head using the same density.

Does rated motor HP determine actual flow?

No. Head, efficiency, pump characteristic and system curve also matter.

Can I use a constant efficiency at all flows?

Only as a stated approximation. Actual pump efficiency varies with operating point.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
  • Grundfos: pump curves, head and operating flowhttps://www.grundfos.com/uk/learn/research-and-insights/pump-curves