Flow rate calculators / Pumps & water systems
Measure flow. Understand the conditions.
Displacement Pump Flow Calculator
Estimate positive-displacement pump delivery from displacement, speed and volumetric efficiency.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Delivered L/min = displacement cm³/rev × RPM × volumetric efficiency / 1,000.
Estimate positive-displacement pump delivery from displacement, speed and volumetric efficiency.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
No relief setting, torque, safe pressure rating or cavitation assessment is made.
Displacement Pump Flow calculation: inputs and interpretation
Volumetric efficiency captures a chosen delivery fraction, not overall energy efficiency. Slip, pressure, viscosity, leakage and wear can affect actual delivery. A pump that traps a fixed geometric volume still needs an appropriate pressure-control and installation design.
A pump operates where its curve meets the system curve. The tools here isolate a stated energy, displacement or test relationship; they do not automatically select a pump or verify suction conditions, cavitation margin, protection or installation requirements.
Continue with: Pump Power Calculator · Pump Flow from Power Calculator · Pump Affinity Laws Calculator · Pool Turnover Flow Calculator
Check the numbers
Displacement Pump Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Geometric displacement = 10 cm³/rev; Shaft speed = 1500 RPM; Volumetric efficiency = 90 %.
| Output | Computed result |
|---|---|
| Nominal displacement-based delivery | 13.5 L/min |
| Geometric delivery before losses | 15 L/min |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 375 RPM | Shaft speed | 3.375 L/min |
| 750 RPM | Shaft speed | 6.75 L/min |
| 1125 RPM | Shaft speed | 10.125 L/min |
| 1500 RPM | Shaft speed | 13.5 L/min |
| 2250 RPM | Shaft speed | 20.25 L/min |
| 3000 RPM | Shaft speed | 27 L/min |
| 4500 RPM | Shaft speed | 40.5 L/min |
Unchanged inputs use: Geometric displacement = 10 cm³/rev; Shaft speed = 1500 RPM; Volumetric efficiency = 90 %. Results retain the model limitations described above.
Common questions
Is volumetric efficiency motor efficiency?
No. It relates delivered volume to geometric displacement, not electrical conversion losses.
Can it estimate a dosing pump?
As volume arithmetic with appropriate displacement and delivery efficiency; calibration may be needed at the actual service conditions.
Does doubling RPM always double actual flow?
Only within a valid approximately fixed-delivery-fraction model and permitted operating range.
Can I use gallons per revolution?
Convert the stated gallon convention to cm³/rev first.
How do I convert cc/rev to L/min?
Multiply displacement in cc/rev by revolutions per minute and by a suitable volumetric efficiency, then divide by 1,000. This estimates positive-displacement delivery; it is not a centrifugal-pump curve.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
- KSB Centrifugal Pump Lexicon: affinity laws and similarity conditionshttps://www.ksb.com/en-global/centrifugal-pump-lexicon/article/affinity-laws-1115682