Flow rate calculators / Gas & compressed air
Measure flow. Understand the conditions.
Compressible Gas Nozzle Calculator
Estimate ideal-gas nozzle mass flow with automatic choked/nonchoked branch selection.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Ideal isentropic nozzle mass flow uses the pressure-ratio relation; below critical ratio [2/(gamma+1)]^[gamma/(gamma−1)], flow is choked.
Estimate ideal-gas nozzle mass flow with automatic choked/nonchoked branch selection.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not an IEC/ISA control-valve model, relief-device design, real-gas pipeline or wet-steam calculation.
Compressible Gas Nozzle calculation: inputs and interpretation
The model uses upstream stagnation pressure and temperature with an effective opening and discharge coefficient. In the choked branch, further reducing the downstream pressure does not raise this ideal throat mass flow. The coefficient is not a substitute for a validated valve or nozzle calibration.
Always distinguish absolute pressure from gauge pressure and absolute temperature from Celsius. Standard and normal volume rates require a stated reference condition. Real-gas properties, moisture and two-phase behavior are included only where explicitly described in the model.
Continue with: ACFM to SCFM Calculator · SCFM to ACFM Calculator · Gas Density Calculator · Wet to Dry Standard Gas Flow Calculator
Check the numbers
Compressible Gas Nozzle Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Effective opening diameter = 5 mm; Upstream stagnation pressure = 500 kPa abs; Downstream pressure = 100 kPa abs; Upstream stagnation temperature = 20 °C; Specific heat ratio = 1.4 ratio; Specific gas constant = 287.05 J/kg/K; Effective discharge coefficient = 0.8 ratio.
| Output | Computed result |
|---|---|
| Ideal-gas nozzle mass-flow estimate | 0.018539 kg/s |
| Mass per hour | 66.74042 kg/h |
| Pressure-ratio branch | Choked ideal-nozzle branch |
| Critical downstream/upstream ratio | 0.528282 ratio |
| Actual pressure ratio | 0.2 ratio |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 25 kPa abs | Downstream pressure | 0.018539 kg/s |
| 50 kPa abs | Downstream pressure | 0.018539 kg/s |
| 75 kPa abs | Downstream pressure | 0.018539 kg/s |
| 100 kPa abs | Downstream pressure | 0.018539 kg/s |
| 150 kPa abs | Downstream pressure | 0.018539 kg/s |
| 200 kPa abs | Downstream pressure | 0.018539 kg/s |
| 300 kPa abs | Downstream pressure | 0.018327 kg/s |
Unchanged inputs use: Effective opening diameter = 5 mm; Upstream stagnation pressure = 500 kPa abs; Downstream pressure = 100 kPa abs; Upstream stagnation temperature = 20 °C; Specific heat ratio = 1.4 ratio; Specific gas constant = 287.05 J/kg/K; Effective discharge coefficient = 0.8 ratio. Results retain the model limitations described above.
Common questions
Does this work for both choked and subsonic discharge?
It selects a pressure-ratio branch under the stated ideal-gas nozzle assumptions.
Can I use gauge pressures?
No. Both pressure inputs must be absolute.
Can I use this for steam through a valve?
Not as a complete steam-sizing method. Phase, real-fluid properties and valve-specific factors can be essential.
Does Cd remove every geometry limitation?
No. A single coefficient cannot make the ideal nozzle model valid for arbitrary devices or two-phase flow.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html