Flow rate calculators / Gas & compressed air
Measure flow. Understand the conditions.
Wet to Dry Standard Gas Flow Calculator
Remove a stated water-vapor fraction from a compatible ideal reference-volume basis.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Dry gas volume at the same reference P,T = wet gas volume × (1−water-vapor mole fraction).
Remove a stated water-vapor fraction from a compatible ideal reference-volume basis.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Does not infer vapor fraction from humidity without temperature and vapor-pressure information.
Wet to Dry Standard Gas Flow calculation: inputs and interpretation
The water fraction is a mole fraction of the wet gas, not relative humidity. This simple calculation assumes compatible reference pressure and temperature and does not model condensation or a changing total basis. DSCFM and SCFM labels must still be checked against actual specifications.
Always distinguish absolute pressure from gauge pressure and absolute temperature from Celsius. Standard and normal volume rates require a stated reference condition. Real-gas properties, moisture and two-phase behavior are included only where explicitly described in the model.
Continue with: ACFM to SCFM Calculator · SCFM to ACFM Calculator · Gas Density Calculator · Compressible Gas Nozzle Calculator
Check the numbers
Wet to Dry Standard Gas Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Wet reference volume flow = 100 reference L/min; Water-vapor mole fraction = 5 %.
| Output | Computed result |
|---|---|
| Compatible-reference dry gas flow | 95 dry reference L/min |
| Removed reference vapor volume | 5 reference L/min |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 1.25 % | Water-vapor mole fraction | 98.75 dry reference L/min |
| 2.5 % | Water-vapor mole fraction | 97.5 dry reference L/min |
| 3.75 % | Water-vapor mole fraction | 96.25 dry reference L/min |
| 5 % | Water-vapor mole fraction | 95 dry reference L/min |
| 7.5 % | Water-vapor mole fraction | 92.5 dry reference L/min |
| 10 % | Water-vapor mole fraction | 90 dry reference L/min |
| 15 % | Water-vapor mole fraction | 85 dry reference L/min |
Unchanged inputs use: Wet reference volume flow = 100 reference L/min; Water-vapor mole fraction = 5 %. Results retain the model limitations described above.
Common questions
Can I enter relative humidity as the water percentage?
No. Relative humidity and water-vapor mole fraction are different quantities.
Does dry flow have less mass than wet flow?
It excludes the water-vapor component; specify what mass or volume basis is being compared.
Can I convert SCFM to DSCFM automatically?
Only after defining reference conditions and actual water-vapor mole fraction.
Does this account for a cold trap?
No. Condensation and separator behavior require an appropriate process model.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html