Flow rate calculators / Airflow & ventilation
Measure flow. Understand the conditions.
Fan Flow from Power Calculator
Estimate an air-volume flow from a stated low-pressure fan energy balance.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Actual Q m³/s = input W × efficiency / pressure increase Pa.
Estimate an air-volume flow from a stated low-pressure fan energy balance.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not an air-compressor horsepower conversion or proof that a real fan curve reaches the calculated point.
Fan Flow from Power calculation: inputs and interpretation
This is a conditional inverse relationship, not a universal HP-to-CFM conversion. Input power, the pressure definition and its corresponding efficiency must describe the same operating point. A motor nameplate maximum does not establish actual consumed power.
An airflow estimate does not certify indoor air quality or determine a code-required ventilation rate. Use the actual operating fan point, measurement plane and air density. Filter loading, duct losses, leakage and balancing can change delivered airflow.
Continue with: Airflow CFM Calculator · Air Changes to CFM Calculator · Bathroom Exhaust Fan Flow Calculator · Fan Power Calculator
Check the numbers
Fan Flow from Power Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Actual input power = 1 kW; Matching fan-system efficiency = 60 %; Specified pressure increase = 250 Pa.
| Output | Computed result |
|---|---|
| Conditional fan energy-balance airflow | 5,085.312008 CFM |
| Volume flow SI | 2.4 m³/s |
| Volume flow hourly | 8,640 m³/h |
| US liquid flow | 38,040.77554 US GPM |
| Cubic feet per minute | 5,085.312008 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.25 kW | Actual input power | 1,271.328002 CFM |
| 0.5 kW | Actual input power | 2,542.656004 CFM |
| 0.75 kW | Actual input power | 3,813.984006 CFM |
| 1 kW | Actual input power | 5,085.312008 CFM |
| 1.5 kW | Actual input power | 7,627.968012 CFM |
| 2 kW | Actual input power | 10,170.624016 CFM |
| 3 kW | Actual input power | 15,255.936024 CFM |
Unchanged inputs use: Actual input power = 1 kW; Matching fan-system efficiency = 60 %; Specified pressure increase = 250 Pa. Results retain the model limitations described above.
Common questions
Can I use 3 HP to find exhaust-fan CFM?
Convert actual mechanical or electrical power with the matching efficiency and specify pressure; HP alone is insufficient.
Can this convert compressor kW to CFM?
Not as a complete high-pressure compressor model. Pressure ratio and thermodynamics require more information.
Does a lower pressure imply greater modeled flow?
At fixed supplied power and efficiency this inverse equation does, but a real fan’s curve and limits still control.
Can I compare free-air ratings?
Only when the rating boundary matches the intended installed condition.
Can I convert CFM to electrical kW or kW to CFM?
Not as a unit conversion. This low-pressure fan relation also needs pressure rise and a consistent total efficiency. A compressor requires a different thermodynamic and performance model; motor rating alone does not establish delivered air.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US Department of Energy: Improving Fan System Performance, pressure-flow power and fan lawshttps://www.energy.gov/sites/default/files/2014/05/f16/fan_sourcebook.pdf
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf