Flow rate calculators / Airflow & ventilation
Measure flow. Understand the conditions.
Airflow CFM Calculator
Calculate imperial rectangular-duct airflow from clear dimensions and an average velocity traverse.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
CFM = velocity FPM × (width inches × height inches / 144).
Calculate imperial rectangular-duct airflow from clear dimensions and an average velocity traverse.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a fan-rating, standard-volume correction or building ventilation approval.
Airflow CFM calculation: inputs and interpretation
The area conversion uses 144 square inches per square foot. The reading must represent mean velocity at that clear section. A centerline reading in a distorted profile, or the exterior grille dimensions rather than effective free area, can misstate delivered airflow.
An airflow estimate does not certify indoor air quality or determine a code-required ventilation rate. Use the actual operating fan point, measurement plane and air density. Filter loading, duct losses, leakage and balancing can change delivered airflow.
Continue with: Air Changes to CFM Calculator · Bathroom Exhaust Fan Flow Calculator · Fan Power Calculator · Fan Flow from Power Calculator
Check the numbers
Airflow CFM Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Clear duct width = 12 inches; Clear duct height = 8 inches; Area-averaged air velocity = 800 ft/min.
| Output | Computed result |
|---|---|
| Local rectangular-duct airflow | 533.333333 CFM |
| Volume flow SI | 0.251705 m³/s |
| Volume flow hourly | 906.139091 m³/h |
| US liquid flow | 3,989.61039 US GPM |
| Cubic feet per minute | 533.333333 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 200 ft/min | Area-averaged air velocity | 133.333333 CFM |
| 400 ft/min | Area-averaged air velocity | 266.666667 CFM |
| 600 ft/min | Area-averaged air velocity | 400 CFM |
| 800 ft/min | Area-averaged air velocity | 533.333333 CFM |
| 1200 ft/min | Area-averaged air velocity | 800 CFM |
| 1600 ft/min | Area-averaged air velocity | 1,066.666667 CFM |
| 2400 ft/min | Area-averaged air velocity | 1,600 CFM |
Unchanged inputs use: Clear duct width = 12 inches; Clear duct height = 8 inches; Area-averaged air velocity = 800 ft/min. Results retain the model limitations described above.
Common questions
Can I convert FPM to CFM without area?
No. Flow is average velocity multiplied by the free section area.
Does CFM here mean SCFM?
No. It is local actual geometric volume flow unless a reference correction is explicitly made.
Can I use grille face dimensions?
Only if they represent the correct effective measurement area; blockage and free-area definitions matter.
Does this calculate fan output from HP?
No. That needs a flow-pressure performance relationship.
What is the CFM calculation formula for ducting or an AHU?
For an actual measurement plane, CFM equals clear area in square feet times mean velocity in feet per minute. This page applies that section relationship. Selecting an AHU or ventilation requirement also needs pressure, outdoor-air requirements and project data.
Can I convert FPM, ft/min or m/s to CFM without duct size?
No. Velocity is distance per time; CFM is volume per time. Supply the relevant clear cross-sectional area, then multiply. Obstructions and nonuniform profiles can make external duct dimensions or a single point reading unsuitable.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html
- US Department of Energy: Improving Fan System Performance, pressure-flow power and fan lawshttps://www.energy.gov/sites/default/files/2014/05/f16/fan_sourcebook.pdf