Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Airflow & ventilation

Measure flow. Understand the conditions.

Fan Power Calculator

Estimate air power and input power at an explicitly defined fan pressure boundary.

Your flow inputs

CFM
Pa
%

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Air power W = actual m³/s × pressure increase Pa; input W = air power / matching efficiency.

Estimate air power and input power at an explicitly defined fan pressure boundary.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Not a fan curve, compressor thermodynamic model or motor selection.

Fan Power calculation: inputs and interpretation

State whether the pressure is static or total and use an efficiency on the same basis. Motor and drive losses must be included in efficiency if the desired output is electrical input. Actual airflow must match the density and operating condition of the measured pressure.

An airflow estimate does not certify indoor air quality or determine a code-required ventilation rate. Use the actual operating fan point, measurement plane and air density. Filter loading, duct losses, leakage and balancing can change delivered airflow.

Check the numbers

Fan Power Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Actual airflow = 1000 CFM; Chosen pressure increase = 250 Pa; Pressure-boundary-to-input efficiency = 60 %.

OutputComputed result
Fan input at chosen pressure/efficiency boundary0.196645 kW
Air power117.986861 W
Mechanical HP equivalent0.263705 HP

How one input changes the answer

ScenarioChanged inputResult
250 CFMActual airflow0.049161 kW
500 CFMActual airflow0.098322 kW
750 CFMActual airflow0.147484 kW
1000 CFMActual airflow0.196645 kW
1500 CFMActual airflow0.294967 kW
2000 CFMActual airflow0.39329 kW
3000 CFMActual airflow0.589934 kW

Unchanged inputs use: Actual airflow = 1000 CFM; Chosen pressure increase = 250 Pa; Pressure-boundary-to-input efficiency = 60 %. Results retain the model limitations described above.

Common questions

Can I convert airflow to horsepower?

Only after providing pressure and a suitable efficiency. CFM alone has no unique power value.

Does a fan’s rated HP determine CFM?

No. The operating point and pressure-flow curve matter.

Is static efficiency interchangeable with total efficiency?

No. Use a pressure and efficiency definition that match.

Can it size a high-pressure compressor?

No. Compressible compression work requires a thermodynamic model beyond Q×small pressure increase.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US Department of Energy: Improving Fan System Performance, pressure-flow power and fan lawshttps://www.energy.gov/sites/default/files/2014/05/f16/fan_sourcebook.pdf
  • US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf