Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Pipe hydraulics

Measure flow. Understand the conditions.

Hazen–Williams Head Loss Calculator

Calculate empirical full-pipe water friction loss from flow, internal diameter and C.

Your flow inputs

L/min
mm
m
coefficient

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Friction head = 10.67 × length × Q^1.852 / (C^1.852 × D^4.871), SI units.

Calculate empirical full-pipe water friction loss from flow, internal diameter and C.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

No elevation, outlet residual, surge or manufacturer performance curve is included.

Hazen–Williams Head Loss calculation: inputs and interpretation

This page starts from measured or specified flow rather than using pressure to infer it. It is useful for checking the friction portion of a water-system head budget. Small bore changes strongly affect the result because diameter appears to a high power.

Pipe losses depend on the model and fluid condition. Inner diameter, roughness, temperature-dependent properties and fittings must be consistent. A result for one straight run does not solve a branched network, select a pressure rating or establish a safe maximum operating flow.

Check the numbers

Hazen–Williams Head Loss Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Volumetric flow = 60 L/min; Actual internal diameter = 50 mm; Straight pipe length = 20 m; Hazen–Williams C = 140 coefficient.

OutputComputed result
Empirical water friction head0.136736 m
Assumed C140 coefficient

How one input changes the answer

ScenarioChanged inputResult
15 L/minVolumetric flow0.010492 m
30 L/minVolumetric flow0.037877 m
45 L/minVolumetric flow0.080259 m
60 L/minVolumetric flow0.136736 m
90 L/minVolumetric flow0.289737 m
120 L/minVolumetric flow0.493617 m
180 L/minVolumetric flow1.04595 m

Unchanged inputs use: Volumetric flow = 60 L/min; Actual internal diameter = 50 mm; Straight pipe length = 20 m; Hazen–Williams C = 140 coefficient. Results retain the model limitations described above.

Common questions

Why does a small diameter change have a large effect?

The empirical SI relationship uses D to approximately the 4.871 power in the denominator.

Can I use this for compressed air?

No. Hazen–Williams is not a compressible-gas sizing equation.

Does a higher C reduce loss?

Within this empirical model, yes at the same flow, length and diameter.

How do I convert head loss to pressure loss?

Multiply head in metres by density and g to obtain pascals, if the density basis is appropriate.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US EPA: EPANET 2.2 hydraulic methods and reference manualhttps://www.epa.gov/water-research/epanet
  • US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf