Flow rate calculators / Pipe hydraulics
Measure flow. Understand the conditions.
Pipe Friction Factor Calculator
Calculate a circular-pipe Darcy factor using laminar theory or an iterative turbulent Colebrook relation.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Laminar Darcy f = 64/Re; turbulent f solves the Colebrook–White equation.
Calculate a circular-pipe Darcy factor using laminar theory or an iterative turbulent Colebrook relation.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
A generic roughness number is not a guarantee for an aged, fouled, corroded or nonstandard pipe.
Pipe Friction Factor calculation: inputs and interpretation
Convert diameter and roughness to the same unit before forming relative roughness. The turbulent calculation solves the implicit relation rather than confusing it with a Fanning factor. This implementation excludes the transitional range from 2,300 to below 4,000 and relative roughness above 0.05.
Pipe losses depend on the model and fluid condition. Inner diameter, roughness, temperature-dependent properties and fittings must be consistent. A result for one straight run does not solve a branched network, select a pressure rating or establish a safe maximum operating flow.
Continue with: Reynolds Number Calculator · Darcy–Weisbach Head Loss Calculator · Pressure to Flow Rate Calculator · Hazen–Williams Flow Calculator
Check the numbers
Pipe Friction Factor Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Reynolds number = 100000 dimensionless; Actual internal diameter = 50 mm; Absolute roughness = 0.045 mm.
| Output | Computed result |
|---|---|
| Pipe friction factor | 0.021832 Darcy f |
| Method | Iterated Colebrook–White |
| Relative roughness | 0.0009 dimensionless |
| Corresponding Fanning factor | 0.005458 Fanning f |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 25000 dimensionless | Reynolds number | 0.026594 Darcy f |
| 50000 dimensionless | Reynolds number | 0.023744 Darcy f |
| 75000 dimensionless | Reynolds number | 0.022526 Darcy f |
| 100000 dimensionless | Reynolds number | 0.021832 Darcy f |
| 150000 dimensionless | Reynolds number | 0.02106 Darcy f |
| 200000 dimensionless | Reynolds number | 0.020635 Darcy f |
| 300000 dimensionless | Reynolds number | 0.020179 Darcy f |
Unchanged inputs use: Reynolds number = 100000 dimensionless; Actual internal diameter = 50 mm; Absolute roughness = 0.045 mm. Results retain the model limitations described above.
Common questions
Why is the transitional range rejected?
A simple laminar or fully turbulent correlation cannot reliably select the actual transitional state.
Can I use the Blasius relation?
It is a smooth-pipe approximation over a limited turbulent range. This tool instead uses Colebrook for its supported turbulent inputs.
Are roughness and diameter both millimetres?
Yes in the form, so their ratio is dimensionless without an extra factor of 1,000.
Is the result Darcy or Fanning?
Darcy. Divide by four only if a downstream calculation explicitly requires Fanning.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
- US EPA: EPANET 2.2 hydraulic methods and reference manualhttps://www.epa.gov/water-research/epanet