Flow rate calculators / Pipe hydraulics
Measure flow. Understand the conditions.
Hazen–Williams Flow Calculator
Estimate water flow in a full pipe from friction head and a supplied Hazen–Williams C coefficient.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
SI Q = [head × C^1.852 × D^4.871 / (10.67 × length)]^(1/1.852).
Estimate water flow in a full pipe from friction head and a supplied Hazen–Williams C coefficient.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Use only within the empirical model’s appropriate water-flow conditions; other head components are excluded.
Hazen–Williams Flow calculation: inputs and interpretation
The numerical coefficient and exponents here use metres, seconds and m³/s internally. This is not a gas correlation, and C is not a Darcy friction factor. The default C is an example, not an assertion about every PVC, steel or aged pipe.
Pipe losses depend on the model and fluid condition. Inner diameter, roughness, temperature-dependent properties and fittings must be consistent. A result for one straight run does not solve a branched network, select a pressure rating or establish a safe maximum operating flow.
Continue with: Reynolds Number Calculator · Darcy–Weisbach Head Loss Calculator · Pressure to Flow Rate Calculator · Pipe Friction Factor Calculator
Check the numbers
Hazen–Williams Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Actual internal diameter = 50 mm; Straight pipe length = 20 m; Friction head available = 5 m; Hazen–Williams C = 140 coefficient.
| Output | Computed result |
|---|---|
| Empirical Hazen–Williams water flow | 418.939235 L/min |
| Volume flow SI | 0.006982 m³/s |
| Volume flow hourly | 25.136354 m³/h |
| US liquid flow | 110.672038 US GPM |
| Cubic feet per minute | 14.794699 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 1.25 m | Friction head available | 198.182201 L/min |
| 2.5 m | Friction head available | 288.142846 L/min |
| 3.75 m | Friction head available | 358.665426 L/min |
| 5 m | Friction head available | 418.939235 L/min |
| 7.5 m | Friction head available | 521.474059 L/min |
| 10 m | Friction head available | 609.107897 L/min |
| 15 m | Friction head available | 758.186249 L/min |
Unchanged inputs use: Actual internal diameter = 50 mm; Straight pipe length = 20 m; Friction head available = 5 m; Hazen–Williams C = 140 coefficient. Results retain the model limitations described above.
Common questions
Can I enter PSI as the head?
Convert the appropriate pressure difference to water head first, using consistent fluid properties.
Is C the same as roughness height?
No. Hazen–Williams C is an empirical coefficient, not a length.
Can this model laminar or high-viscosity flow?
The empirical relationship may be unsuitable. Use an appropriate fluid-mechanics model instead.
Does this include fittings?
Not automatically. The form describes a straight-run friction budget.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US EPA: EPANET 2.2 hydraulic methods and reference manualhttps://www.epa.gov/water-research/epanet
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf