Flow rate calculators / Pipe hydraulics
Measure flow. Understand the conditions.
Pressure to Flow Rate Calculator
Estimate full-pipe flow from a specified friction-pressure budget, geometry and fixed Darcy factor.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Q = pipe area × √[2 × pressure drop × D / (density × fixed Darcy f × length)].
Estimate full-pipe flow from a specified friction-pressure budget, geometry and fixed Darcy factor.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
The fixed-factor approximation does not solve Reynolds-dependent friction, a network, a pump curve or compressible gas flow.
Pressure to Flow Rate calculation: inputs and interpretation
PSI, bar or kPa cannot be converted to GPM or L/min by a unit multiplier. This page supplies one particular resistance model: a straight full pipe with constant Darcy factor. The available pressure here is the amount allocated to friction after other head components have been handled.
Pipe losses depend on the model and fluid condition. Inner diameter, roughness, temperature-dependent properties and fittings must be consistent. A result for one straight run does not solve a branched network, select a pressure rating or establish a safe maximum operating flow.
Continue with: Reynolds Number Calculator · Darcy–Weisbach Head Loss Calculator · Pipe Friction Factor Calculator · Hazen–Williams Flow Calculator
Check the numbers
Pressure to Flow Rate Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Pressure difference available for friction = 20 ; Pressure difference unit = psi; Actual internal diameter = 50 mm; Straight pipe length = 20 m; Fixed Darcy friction factor = 0.02 ratio; Fluid density = 998 kg/m³.
| Output | Computed result |
|---|---|
| Fixed-factor pressure-driven flow | 182.914121 US GPM |
| Modeled average velocity | 5.877318 m/s |
| Friction differential | 137.895146 kPa |
| Volume flow SI | 0.01154 m³/s |
| Volume flow hourly | 41.544316 m³/h |
| US liquid flow | 182.914121 US GPM |
| Cubic feet per minute | 24.452061 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 5 | Pressure difference available for friction | 91.45706 US GPM |
| 10 | Pressure difference available for friction | 129.339815 US GPM |
| 15 | Pressure difference available for friction | 158.408275 US GPM |
| 20 | Pressure difference available for friction | 182.914121 US GPM |
| 30 | Pressure difference available for friction | 224.023131 US GPM |
| 40 | Pressure difference available for friction | 258.67963 US GPM |
| 60 | Pressure difference available for friction | 316.81655 US GPM |
Unchanged inputs use: Pressure difference available for friction = 20 ; Pressure difference unit = psi; Actual internal diameter = 50 mm; Straight pipe length = 20 m; Fixed Darcy friction factor = 0.02 ratio; Fluid density = 998 kg/m³. Results retain the model limitations described above.
Common questions
Can I convert GPM to PSI directly?
No. Pressure and flow have different dimensions; a hydraulic model or measured device coefficient is required.
Does supply pressure all become pipe friction?
Not necessarily. Elevation, residual pressure, fittings and equipment can consume part of the available head.
Can I use a pipe’s outside diameter?
No. Use actual internal diameter and the correct straight-run length.
Does this determine maximum safe flow?
No. It estimates one modeled operating flow without certifying velocity, pressure rating or installation requirements.
Is PSI to GPM, bar to LPM or Pa to CFM a direct conversion?
No. Pressure and volume rate are different quantities. This page uses a stated full-liquid-pipe resistance model with diameter, length, density and a supplied Darcy factor. Gas flow and calibrated valve or nozzle flow require their appropriate tools.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
- US EPA: EPANET 2.2 hydraulic methods and reference manualhttps://www.epa.gov/water-research/epanet