Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Open channels & drainage

Measure flow. Understand the conditions.

Froude Number Calculator

Calculate an open-channel Froude number from velocity, wetted area and surface width.

Your flow inputs

m/s
m²
m

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Hydraulic depth=A/top width; Froude number=v/√(g×hydraulic depth).

Calculate an open-channel Froude number from velocity, wetted area and surface width.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Does not locate a hydraulic jump or solve its downstream depth.

Froude Number calculation: inputs and interpretation

Hydraulic depth is area divided by free-surface top width, which differs from hydraulic radius. The ratio compares mean flow speed with a simple gravity-wave scale. The regime labels apply to this hydraulic representation, not every possible wave or two-phase condition.

Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.

Check the numbers

Froude Number Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Mean flow velocity = 1 m/s; Wetted area = 0.5 m²; Free-surface top width = 1 m.

OutputComputed result
Open-channel Froude number0.451601 dimensionless
Hydraulic depth0.5 m
Model regimeSubcritical

How one input changes the answer

ScenarioChanged inputResult
0.25 m/sMean flow velocity0.1129 dimensionless
0.5 m/sMean flow velocity0.2258 dimensionless
0.75 m/sMean flow velocity0.338701 dimensionless
1 m/sMean flow velocity0.451601 dimensionless
1.5 m/sMean flow velocity0.677401 dimensionless
2 m/sMean flow velocity0.903202 dimensionless
3 m/sMean flow velocity1.354802 dimensionless

Unchanged inputs use: Mean flow velocity = 1 m/s; Wetted area = 0.5 m²; Free-surface top width = 1 m. Results retain the model limitations described above.

Common questions

Is hydraulic depth the same as hydraulic radius?

No. Hydraulic radius uses wetted perimeter; hydraulic depth uses free-surface top width.

What does a value near one mean?

It represents the critical condition within the stated open-channel model; numerical proximity alone is not a complete flow diagnosis.

Can I use a fully pressurized pipe?

This free-surface definition needs a meaningful top width and open-channel context.

Does it calculate water-surface profiles?

No. It reports the supplied section’s dimensionless ratio.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US National Weather Service: Normal Depth Demonstration Tool and Manning equationhttps://www.weather.gov/aprfc/normaldepthcalc
  • US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf