Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Normal Depth Calculator
Numerically solve uniform-flow normal depth for a rectangular or trapezoidal section.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Find positive y satisfying SI Q = A(y) [A(y)/P(y)]^(2/3) √S/n.
Numerically solve uniform-flow normal depth for a rectangular or trapezoidal section.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a backwater, unsteady flood routing or culvert inlet solution.
Normal Depth calculation: inputs and interpretation
A zero side slope gives vertical walls and a rectangular section. The calculation brackets the positive depth and uses bisection; it does not claim that this uniform depth occurs everywhere in a real channel. Boundary conditions, controls and transitions may create a different water-surface profile.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Froude Number Calculator
Check the numbers
Normal Depth Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Required discharge = 0.3 m³/s; Bottom width = 1 m; Symmetric side slope H:V = 0 ratio; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m.
| Output | Computed result |
|---|---|
| Modeled uniform normal depth | 0.352665 m |
| Discharge verification | 0.3 m³/s |
| Wetted area | 0.352665 m² |
| Mean velocity | 0.850666 m/s |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.075 m³/s | Required discharge | 0.136569 m |
| 0.15 m³/s | Required discharge | 0.217103 m |
| 0.225 m³/s | Required discharge | 0.287461 m |
| 0.3 m³/s | Required discharge | 0.352665 m |
| 0.45 m³/s | Required discharge | 0.474476 m |
| 0.6 m³/s | Required discharge | 0.589631 m |
| 0.9 m³/s | Required discharge | 0.809373 m |
Unchanged inputs use: Required discharge = 0.3 m³/s; Bottom width = 1 m; Symmetric side slope H:V = 0 ratio; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m. Results retain the model limitations described above.
Common questions
What is normal depth?
The depth that satisfies the stated uniform-flow resistance balance for the entered discharge and section.
Is normal depth the same as critical depth?
No. Critical depth is an energy/flow-regime condition; normal depth is a resistance-and-slope condition.
Can I use a zero slope?
Not for a positive uniform-flow discharge in this model.
How is the depth solved?
By bracketing and bisection of the monotonic supported section’s Manning discharge function.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US National Weather Service: Normal Depth Demonstration Tool and Manning equationhttps://www.weather.gov/aprfc/normaldepthcalc