Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Rectangular Channel Flow Calculator
Calculate steady uniform free-surface flow in a rectangular channel using Manning’s equation.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
SI Manning Q = area × hydraulic radius^(2/3) × √slope / n; rectangle area=b×y, wetted perimeter=b+2y.
Calculate steady uniform free-surface flow in a rectangular channel using Manning’s equation.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not an inlet-controlled box-culvert, backwater, pressurized conduit or flood design.
Rectangular Channel Flow calculation: inputs and interpretation
The depth is water depth, not wall height. Hydraulic radius uses wetted area divided by wetted perimeter, excluding the open top. Under uniform flow the energy slope can be represented by the channel slope; backwater or acceleration can break that assumption.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Normal Depth Calculator · Froude Number Calculator
Check the numbers
Rectangular Channel Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Bottom width = 1 m; Flow depth = 0.5 m; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m.
| Output | Computed result |
|---|---|
| Uniform-channel Manning discharge | 0.482673 m³/s |
| Wetted area | 0.5 m² |
| Hydraulic radius | 0.25 m |
| Mean velocity | 0.965347 m/s |
| Volume flow SI | 0.482673 m³/s |
| Volume flow hourly | 1,737.624075 m³/h |
| US liquid flow | 7,650.528637 US GPM |
| Cubic feet per minute | 1,022.726918 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.125 m | Flow depth | 0.065509 m³/s |
| 0.25 m | Flow depth | 0.184174 m³/s |
| 0.375 m | Flow depth | 0.326651 m³/s |
| 0.5 m | Flow depth | 0.482673 m³/s |
| 0.75 m | Flow depth | 0.817583 m³/s |
| 1 m | Flow depth | 1.169434 m³/s |
| 1.5 m | Flow depth | 1.897443 m³/s |
Unchanged inputs use: Bottom width = 1 m; Flow depth = 0.5 m; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m. Results retain the model limitations described above.
Common questions
Does this calculate a box culvert’s full capacity?
Only a uniform free-surface barrel-flow scenario. Culvert inlet, outlet, headwater and tailwater controls are not modeled.
Is hydraulic radius the same as water depth?
Only approximately for a very wide shallow rectangle. This tool uses the exact rectangular wetted perimeter.
Can I use the US Manning coefficient 1.486?
This form uses SI geometry and the SI coefficient 1, not the US customary coefficient.
Is n automatically chosen from material?
No. Supply a justified roughness value for the channel condition.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US National Weather Service: Normal Depth Demonstration Tool and Manning equationhttps://www.weather.gov/aprfc/normaldepthcalc
- US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html