Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Partially Full Pipe Flow Calculator
Apply circular-segment geometry and SI Manning flow to a specified partly full gravity pipe.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
theta=2 acos(1−2y/D); area=D²(theta−sin theta)/8; wetted perimeter=D theta/2; Q=A R^(2/3)√S/n.
Apply circular-segment geometry and SI Manning flow to a specified partly full gravity pipe.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a sewer network, surcharge, air-entrapment or inlet/outlet-control solution.
Partially Full Pipe Flow calculation: inputs and interpretation
The central angle is in radians, and only the wetted arc contributes to the perimeter. The calculation approaches the full circular geometry at depth equal to diameter, but a truly pressurized pipe requires a pressure-flow analysis. Water depth cannot exceed the actual internal diameter.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Normal Depth Calculator · Froude Number Calculator
Check the numbers
Partially Full Pipe Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Circular internal diameter = 0.3 m; Water depth above invert = 0.15 m; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m.
| Output | Computed result |
|---|---|
| Circular open-section Manning discharge | 0.01529 m³/s |
| Wetted area | 0.035343 m² |
| Hydraulic radius | 0.075 m |
| Depth / diameter | 0.5 ratio |
| Volume flow SI | 0.01529 m³/s |
| Volume flow hourly | 55.043037 m³/h |
| US liquid flow | 242.3472 US GPM |
| Cubic feet per minute | 32.397108 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.0375 m | Water depth above invert | 0.001018 m³/s |
| 0.075 m | Water depth above invert | 0.004189 m³/s |
| 0.1125 m | Water depth above invert | 0.009149 m³/s |
| 0.15 m | Water depth above invert | 0.01529 m³/s |
| 0.225 m | Water depth above invert | 0.027885 m³/s |
| 0.3 m | Water depth above invert | 0.030579 m³/s |
Unchanged inputs use: Circular internal diameter = 0.3 m; Water depth above invert = 0.15 m; Manning roughness n = 0.013 SI basis; Energy slope = 0.001 m/m. Results retain the model limitations described above.
Common questions
Is flow proportional to the depth fraction?
No. Both area and hydraulic radius change nonlinearly with depth.
Can I enter depth greater than diameter?
No. That is outside the circular open-section geometry.
Does it calculate full pressurized flow?
No. Even the full-depth limit is a Manning uniform-flow representation, not a pressure-network model.
Can I determine normal depth here?
This tool evaluates a given depth. The normal-depth tool solves a supported trapezoidal section from specified flow.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US National Weather Service: Normal Depth Demonstration Tool and Manning equationhttps://www.weather.gov/aprfc/normaldepthcalc
- US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html