Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Flow fundamentals

Measure flow. Understand the conditions.

Volume Flow from Mass Flow Calculator

Find local volume flow from mass flow and a specified density.

Your flow inputs

kg/s
kg/m³

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Volume flow m³/s = mass flow kg/s / density kg/m³.

Find local volume flow from mass flow and a specified density.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This does not establish gas standard conditions or identify fluid properties from its name.

Volume Flow from Mass Flow calculation: inputs and interpretation

A mass-flow value alone cannot determine a volume rate. One kilogram per second of a dense liquid occupies far less volume than one kilogram per second of low-pressure air. Temperature, pressure and composition therefore belong to the density specification.

Keep the same time basis when comparing readings. A volume total, an average rate and an instantaneous meter value answer different questions. Use the actual wetted section or measured fluid quantity rather than an outside pipe dimension or an equipment nameplate that does not describe the operating condition.

Check the numbers

Volume Flow from Mass Flow Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Mass flow = 1 kg/s; Fluid density = 998 kg/m³.

OutputComputed result
Local volume flow from mass60.12024 L/min
Mass flow1 kg/s
Volume flow SI0.001002 m³/s
Volume flow hourly3.607214 m³/h
US liquid flow15.882087 US GPM
Cubic feet per minute2.123126 CFM

How one input changes the answer

ScenarioChanged inputResult
0.25 kg/sMass flow15.03006 L/min
0.5 kg/sMass flow30.06012 L/min
0.75 kg/sMass flow45.09018 L/min
1 kg/sMass flow60.12024 L/min
1.5 kg/sMass flow90.180361 L/min
2 kg/sMass flow120.240481 L/min
3 kg/sMass flow180.360721 L/min

Unchanged inputs use: Mass flow = 1 kg/s; Fluid density = 998 kg/m³. Results retain the model limitations described above.

Common questions

Can I convert kg/s to CFM?

Yes only after choosing a matching local gas density. CFM is a volume rate, not mass.

Can lb/h convert to GPM?

Convert mass units first and supply fluid density. US and Imperial GPM also differ.

Does steam volume remain constant at different pressures?

No. The density can change greatly, so use the actual thermodynamic state.

Can I infer density from temperature alone?

Not generally. Pressure, composition and phase can also matter.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html
  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9