Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Broad-Crested Weir Calculator
Estimate a broad-crest discharge from an ideal critical-control relationship and explicit coefficient.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Ideal rectangular critical-crest Q = Cd × width × √g × (2H/3)^(3/2).
Estimate a broad-crest discharge from an ideal critical-control relationship and explicit coefficient.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a submerged structure, dam-safety or complete weir design calculation.
Broad-Crested Weir calculation: inputs and interpretation
The head here is the appropriate upstream specific-energy head relative to crest elevation. Whether a real crest is long enough, aerated and free from downstream control must be established separately. The coefficient is a chosen scenario value, not a universal calibration.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Normal Depth Calculator
Check the numbers
Broad-Crested Weir Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Crest flow width = 1 m; Upstream specific head above crest = 0.3 m; Chosen coefficient = 0.95 ratio.
| Output | Computed result |
|---|---|
| Ideal broad-crest coefficient estimate | 0.26609 m³/s |
| Volume flow SI | 0.26609 m³/s |
| Volume flow hourly | 957.924845 m³/h |
| US liquid flow | 4,217.616205 US GPM |
| Cubic feet per minute | 563.813277 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.075 m | Upstream specific head above crest | 0.033261 m³/s |
| 0.15 m | Upstream specific head above crest | 0.094077 m³/s |
| 0.225 m | Upstream specific head above crest | 0.172831 m³/s |
| 0.3 m | Upstream specific head above crest | 0.26609 m³/s |
| 0.45 m | Upstream specific head above crest | 0.488839 m³/s |
| 0.6 m | Upstream specific head above crest | 0.752617 m³/s |
| 0.9 m | Upstream specific head above crest | 1.382645 m³/s |
Unchanged inputs use: Crest flow width = 1 m; Upstream specific head above crest = 0.3 m; Chosen coefficient = 0.95 ratio. Results retain the model limitations described above.
Common questions
Is this the same as a sharp-crested rectangular weir?
No. The critical-crest model and its coefficient definition differ.
Does crest length along flow matter?
Yes to whether the physical structure meets the model assumptions, although it is not a correction input here.
Can I use a water-level reading as total specific head?
Only if approach-velocity and reference-datum effects are handled appropriately.
Does this select a safe structure size?
No. It evaluates a stated hydraulic model only.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US Bureau of Reclamation Water Measurement Manual, Chapter 7: weirs and operating conditionshttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap07_04.html
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf