Flow rate calculators / Heat & industrial applications
Measure flow. Understand the conditions.
Water Flow Heat Transfer Calculator
Calculate sensible thermal power carried by a specified liquid flow and temperature change.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Thermal power W = density × volume flow × specific heat × temperature change.
Calculate sensible thermal power carried by a specified liquid flow and temperature change.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
This does not infer electrical input power or efficiency of the heat source.
Water Flow Heat Transfer calculation: inputs and interpretation
Use temperatures and flow that describe the same stream and representative interval. A heating/cooling load estimate can be misleading if a meter reads intermittent flow while the temperature difference is taken from another period. Phase changes require enthalpy rather than this constant-cp form.
The inputs must describe the actual process boundary. Fluid properties, temperature or enthalpy change and equipment behavior can vary during operation. The displayed equations are preliminary calculations and do not implement proprietary equipment performance maps.
Continue with: Heating & Chilled Water Flow Calculator · Steam Mass Flow from Heat Duty Calculator · Counterflow Heat Exchanger LMTD Calculator · Carburetor CFM Calculator
Check the numbers
Water Flow Heat Transfer Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Volumetric flow = 60 L/min; Temperature change magnitude = 5 K; Fluid density = 998 kg/m³; Specific heat = 4180 J/kg/K.
| Output | Computed result |
|---|---|
| Sensible heat carried by liquid | 20.8582 kW thermal |
| IT thermal units per hour | 71,171.132612 Btu/h |
| Mechanical/electrical input | Not inferred |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 15 L/min | Volumetric flow | 5.21455 kW thermal |
| 30 L/min | Volumetric flow | 10.4291 kW thermal |
| 45 L/min | Volumetric flow | 15.64365 kW thermal |
| 60 L/min | Volumetric flow | 20.8582 kW thermal |
| 90 L/min | Volumetric flow | 31.2873 kW thermal |
| 120 L/min | Volumetric flow | 41.7164 kW thermal |
| 180 L/min | Volumetric flow | 62.5746 kW thermal |
Unchanged inputs use: Volumetric flow = 60 L/min; Temperature change magnitude = 5 K; Fluid density = 998 kg/m³; Specific heat = 4180 J/kg/K. Results retain the model limitations described above.
Common questions
Is carried heat the same as electricity used?
No. A heater, heat pump or chiller connects thermal power to purchased energy through its actual performance.
Can I calculate water BTU/h from GPM?
With a specified temperature change and matching fluid properties, yes; the result includes an IT Btu/h readout.
Does it model boiling or condensing steam?
No. Use an enthalpy-based energy balance for phase change.
Can I use an average flow and average temperature difference?
Only when that combination represents the average product accurately; correlations and cycling can matter.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 2: sensible heat and LMTDhttps://archives.standards.doxcelerate.com/documents/doe-hdbk-1012-2-92-thermodynamics-heat-transfer-and-fluid-flow-volume-2-of-3
- NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9