Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Darcy Groundwater Flow Calculator
Calculate a simple saturated Darcy discharge and an effective-porosity pore-velocity estimate.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Darcy discharge Q = hydraulic conductivity × area × gradient; average pore velocity = conductivity × gradient / effective porosity.
Calculate a simple saturated Darcy discharge and an effective-porosity pore-velocity estimate.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not an aquifer model, contaminant travel-time guarantee or unsaturated-flow solution.
Darcy Groundwater Flow calculation: inputs and interpretation
Hydraulic conductivity is not intrinsic permeability. Darcy flux represents discharge per total area, while average pore velocity accounts for the effective connected pore fraction. The simple relationship assumes a suitable saturated continuum and direction of gradient.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Normal Depth Calculator
Check the numbers
Darcy Groundwater Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Hydraulic conductivity = 0.0001 m/s; Flow cross-section area = 10 m²; Hydraulic head gradient = 0.01 m/m; Effective porosity = 0.25 ratio.
| Output | Computed result |
|---|---|
| Saturated Darcy discharge | 1.0e-5 m³/s |
| Darcy flux | 1.0e-6 m/s |
| Average pore-velocity estimate | 4.0e-6 m/s |
| Volume flow SI | 1.0e-5 m³/s |
| Volume flow hourly | 0.036 m³/h |
| US liquid flow | 0.158503 US GPM |
| Cubic feet per minute | 0.021189 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.0025 m/m | Hydraulic head gradient | 2.5e-6 m³/s |
| 0.005 m/m | Hydraulic head gradient | 5.0e-6 m³/s |
| 0.0075 m/m | Hydraulic head gradient | 7.5e-6 m³/s |
| 0.01 m/m | Hydraulic head gradient | 1.0e-5 m³/s |
| 0.015 m/m | Hydraulic head gradient | 1.5e-5 m³/s |
| 0.02 m/m | Hydraulic head gradient | 2.0e-5 m³/s |
| 0.03 m/m | Hydraulic head gradient | 3.0e-5 m³/s |
Unchanged inputs use: Hydraulic conductivity = 0.0001 m/s; Flow cross-section area = 10 m²; Hydraulic head gradient = 0.01 m/m; Effective porosity = 0.25 ratio. Results retain the model limitations described above.
Common questions
Is Darcy flux the same as pore-water speed?
No. Dividing Darcy flux by effective porosity gives a simple average pore velocity under the model.
Can I use permeability in m² as conductivity?
Not unchanged. Hydraulic conductivity also depends on fluid properties.
Does this model fractures explicitly?
No. The continuum inputs must be appropriate to the flow regime.
Does it predict a safe pumping yield?
No. That requires hydrogeological analysis beyond this cross-section calculation.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- USGS Open-File Report 90-183: Darcy flow and the Thiem confined-radial-flow derivationhttps://pubs.usgs.gov/of/1990/ofr90-183/pdf/ofr_90-183_e.pdf