Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Valves & flow measurement

Measure flow. Understand the conditions.

Orifice Diameter from Flow Calculator

Invert the simple liquid-orifice model to estimate opening diameter for a target flow.

Your flow inputs

L/min
kPa
kg/m³
ratio

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Opening area = Q/[Cd√(2Δp/ρ)]; diameter = √(4 area/π).

Invert the simple liquid-orifice model to estimate opening diameter for a target flow.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is a preliminary incompressible opening calculation, not a control-valve, cavitation or gas-capacity design.

Orifice Diameter from Flow calculation: inputs and interpretation

The result is an ideal round opening under the supplied coefficient and differential pressure. A manufactured nozzle may have a different effective area and calibrated coefficient. Convert the required flow to local volume flow before comparing with a product rating.

Discharge and valve coefficients describe a specific device and test basis. The examples are not certified calibrations. Pressure-tap arrangement, density, Reynolds number and downstream conditions can change the relationship between a measured pressure difference and actual flow.

Check the numbers

Orifice Diameter from Flow Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Volumetric flow = 60 L/min; Pressure difference = 100 kPa; Fluid density = 998 kg/m³; Discharge coefficient = 0.62 ratio.

OutputComputed result
Theoretical opening diameter12.044377 mm
Opening area0.000114 m²

How one input changes the answer

ScenarioChanged inputResult
15 L/minVolumetric flow6.022189 mm
30 L/minVolumetric flow8.516661 mm
45 L/minVolumetric flow10.430737 mm
60 L/minVolumetric flow12.044377 mm
90 L/minVolumetric flow14.751289 mm
120 L/minVolumetric flow17.033322 mm
180 L/minVolumetric flow20.861473 mm

Unchanged inputs use: Volumetric flow = 60 L/min; Pressure difference = 100 kPa; Fluid density = 998 kg/m³; Discharge coefficient = 0.62 ratio. Results retain the model limitations described above.

Common questions

Does it select a standard drill or nozzle size?

No. It reports a continuous theoretical diameter; verify a real product’s measured performance.

What if the pressure difference is zero?

A positive target flow cannot be obtained from this finite passive-orifice model at zero differential pressure.

Can I use it for an air-flow orifice?

Not for compressible conditions. Gas density and choking require a suitable model.

Should I include a pipe beta ratio?

This simple large-upstream-area model does not include that effect. Use an appropriate meter equation for a finite approach pipe.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf