Flow rate calculators / Flow fundamentals
Measure flow. Understand the conditions.
Mass & Volume Flow Converter
Convert kg/h, kg/s or lb-based rates to L/min, US GPM or m³/h using an explicit density.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Mass rate SI = density × volume rate SI; unit factors are applied before and after this relationship.
Convert kg/h, kg/s or lb-based rates to L/min, US GPM or m³/h using an explicit density.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
No fluid-property lookup, fuel composition or reference-condition correction is automatic.
Mass & Volume Flow Converter: inputs and interpretation
In the forward direction the known value uses the selected mass unit; in reverse it uses the selected volume unit. The density must describe that volume basis. An actual gas density and a standard volume cannot be combined as though they referred to the same condition.
Keep the same time basis when comparing readings. A volume total, an average rate and an instantaneous meter value answer different questions. Use the actual wetted section or measured fluid quantity rather than an outside pipe dimension or an equipment nameplate that does not describe the operating condition.
Continue with: Flow Rate Calculator · Pipe Flow Rate Calculator · Flow Velocity Calculator · Pipe Diameter from Flow Calculator
Check the numbers
Mass & Volume Flow Converter: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Known rate value = 1 ; Conversion direction = Mass rate to volume rate; Mass-rate unit = kg/h; Volume-rate unit = L/min; Density at matching condition = 1000 kg/m³.
| Output | Computed result |
|---|---|
| Matching-density mass/volume conversion | 0.016667 L/min |
| Supplied density | 1,000 kg/m³ |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.25 | Known rate value | 0.004167 L/min |
| 0.5 | Known rate value | 0.008333 L/min |
| 0.75 | Known rate value | 0.0125 L/min |
| 1 | Known rate value | 0.016667 L/min |
| 1.5 | Known rate value | 0.025 L/min |
| 2 | Known rate value | 0.033333 L/min |
| 3 | Known rate value | 0.05 L/min |
Unchanged inputs use: Known rate value = 1 ; Conversion direction = Mass rate to volume rate; Mass-rate unit = kg/h; Volume-rate unit = L/min; Density at matching condition = 1000 kg/m³. Results retain the model limitations described above.
Common questions
How do I convert kg/h to L/min?
Divide mass per hour by matching density to obtain volume per hour, then convert to litres per minute. The selector performs those steps.
Can I convert lb/h to GPM?
Yes with the exact stated pound and US-gallon conventions plus an appropriate density.
What units does the known value use?
The selected mass unit in forward mode, and the selected volume unit in reverse mode.
Does the default density identify my liquid?
No. It is a chosen example; use validated properties at the actual pressure, temperature and composition.
Is PPH the same as lb/h when converting to GPM?
PPH often means pounds per hour; confirm the originating document. Select lb/h and supply density at the same volume reference condition. A thousand pounds per hour notation such as kpph must first be scaled by 1,000.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html
- NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9