Flow rate calculators / Pumps & water systems
Measure flow. Understand the conditions.
Hydrant Residual Pressure Flow Calculator
Apply the documented residual-pressure extrapolation to entered hydrant test values.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Estimated Qtarget = Qtest × [(Pstatic−Ptarget)/(Pstatic−Presidual)]^0.54.
Apply the documented residual-pressure extrapolation to entered hydrant test values.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Does not determine required fire flow, test acceptance, marking, system adequacy or current code compliance.
Hydrant Residual Pressure Flow calculation: inputs and interpretation
This is a historical documented extrapolation relationship, not a certification that a test satisfies the currently adopted NFPA edition. Use representative simultaneous readings, appropriate discharge measurements and a justified target residual. Extrapolation cannot repair a poor test or model every supply-network change.
A pump operates where its curve meets the system curve. The tools here isolate a stated energy, displacement or test relationship; they do not automatically select a pump or verify suction conditions, cavitation margin, protection or installation requirements.
Continue with: Pump Power Calculator · Pump Flow from Power Calculator · Pump Affinity Laws Calculator · Displacement Pump Flow Calculator
Check the numbers
Hydrant Residual Pressure Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Static test pressure = 60 psi; Residual pressure during test = 40 psi; Measured test discharge = 500 US GPM; Chosen target residual pressure = 20 psi.
| Output | Computed result |
|---|---|
| Historical-method residual-flow extrapolation | 726.986259 US GPM |
| Chosen target residual | 20 psi |
| Extrapolation factor | 1.453973 ratio |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 125 US GPM | Measured test discharge | 181.746565 US GPM |
| 250 US GPM | Measured test discharge | 363.493129 US GPM |
| 375 US GPM | Measured test discharge | 545.239694 US GPM |
| 500 US GPM | Measured test discharge | 726.986259 US GPM |
| 750 US GPM | Measured test discharge | 1,090.479388 US GPM |
| 1000 US GPM | Measured test discharge | 1,453.972517 US GPM |
| 1500 US GPM | Measured test discharge | 2,180.958776 US GPM |
Unchanged inputs use: Static test pressure = 60 psi; Residual pressure during test = 40 psi; Measured test discharge = 500 US GPM; Chosen target residual pressure = 20 psi. Results retain the model limitations described above.
Common questions
Why does the example use 20 psi?
It illustrates a common target in the referenced method. This site does not select the applicable required target for your jurisdiction or project.
Can it determine a building’s required fire flow?
No. It estimates a supply relationship from test data; required demand is a separate design determination.
What input relationships are required?
Static pressure must exceed measured residual and be at least the target; otherwise this model is not meaningful.
Is the NFPA source a current adopted standard?
The cited public report documents the method context. It is not represented as a current compliance authority or an adopted edition.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- NFPA 291 public input report: hydrant residual-pressure flow relationship; historical method reference, not current compliance certificationhttps://www.nfpa.org/api/files?path=%2Ffiles%2FAboutTheCodes%2F291%2F291_A2021_AUT_PRI_PIReport.pdf
- US DOE Fundamentals Handbook, Thermodynamics, Heat Transfer and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf