Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Rational Method Runoff Calculator
Calculate a stated Rational Method peak-runoff scenario from coefficient, rainfall intensity and drainage area.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Peak runoff m³/s = runoff coefficient × intensity(mm/h) × area(ha) / 360.
Calculate a stated Rational Method peak-runoff scenario from coefficient, rainfall intensity and drainage area.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a flood-frequency model, routing hydrograph or complete stormwater/culvert design.
Rational Method Runoff calculation: inputs and interpretation
The factor follows SI area and time conversion. Selecting an appropriate design intensity requires storm duration, time of concentration, frequency and local data; none is fetched by this tool. The chosen coefficient does not reproduce every land-use or soil condition.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Normal Depth Calculator
Check the numbers
Rational Method Runoff Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Chosen runoff coefficient = 0.7 ratio; Applicable rainfall intensity = 50 mm/h; Drainage area = 1 hectares.
| Output | Computed result |
|---|---|
| Rational Method peak scenario | 0.097222 m³/s |
| Volume flow SI | 0.097222 m³/s |
| Volume flow hourly | 350 m³/h |
| US liquid flow | 1,541.003639 US GPM |
| Cubic feet per minute | 206.002223 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 12.5 mm/h | Applicable rainfall intensity | 0.024306 m³/s |
| 25 mm/h | Applicable rainfall intensity | 0.048611 m³/s |
| 37.5 mm/h | Applicable rainfall intensity | 0.072917 m³/s |
| 50 mm/h | Applicable rainfall intensity | 0.097222 m³/s |
| 75 mm/h | Applicable rainfall intensity | 0.145833 m³/s |
| 100 mm/h | Applicable rainfall intensity | 0.194444 m³/s |
| 150 mm/h | Applicable rainfall intensity | 0.291667 m³/s |
Unchanged inputs use: Chosen runoff coefficient = 0.7 ratio; Applicable rainfall intensity = 50 mm/h; Drainage area = 1 hectares. Results retain the model limitations described above.
Common questions
Does this retrieve rainfall for my address?
No. Supply a verified intensity appropriate to the design method and site.
Does it produce a hydrograph?
No. It reports a single peak estimate under the stated Rational Method inputs.
Is the default coefficient prescribed?
No. It is illustrative and must be justified for the application.
Can I use it to approve a culvert?
No. Culvert controls, headwater, tailwater and site requirements need separate analysis.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- Texas Department of Transportation: Rational Method, peak runoff and required inputshttps://www.txdot.gov/content/txdotoms/us/en/manuals/des/hyd/chapter-4--hydrology/section-12--rational-method/procedure-for-using-the-rational-method.html
- NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9