Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Airflow & ventilation

Measure flow. Understand the conditions.

Compressor Receiver Fill Time Calculator

Estimate ideal isothermal receiver filling time from a constant reference-volume delivery.

Your flow inputs

L
kPa abs
kPa abs
kPa abs
reference L/min

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Ideal time min = receiver L × (final−initial absolute kPa) / (reference kPa × free-air L/min).

Estimate ideal isothermal receiver filling time from a constant reference-volume delivery.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Not a compressor capacity certification, thermal transient or pressure-vessel safety assessment.

Compressor Receiver Fill Time calculation: inputs and interpretation

The tank gas and reference gas are assumed to share a constant temperature with ideal behavior. Compressor delivery is referenced free-air volume, not compressed volume inside the receiver. Leakage, load cycling, rising temperature and changing delivery pressure can substantially alter actual time.

An airflow estimate does not certify indoor air quality or determine a code-required ventilation rate. Use the actual operating fan point, measurement plane and air density. Filter loading, duct losses, leakage and balancing can change delivered airflow.

Check the numbers

Compressor Receiver Fill Time Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Receiver internal volume = 100 L; Starting absolute pressure = 100 kPa abs; Final absolute pressure = 800 kPa abs; Free-air reference pressure = 101.325 kPa abs; Constant free-air delivery = 100 reference L/min.

OutputComputed result
Ideal isothermal receiver fill duration6.908463 minutes
Required reference gas volume690.846287 L

How one input changes the answer

ScenarioChanged inputResult
25 reference L/minConstant free-air delivery27.633851 minutes
50 reference L/minConstant free-air delivery13.816926 minutes
75 reference L/minConstant free-air delivery9.211284 minutes
100 reference L/minConstant free-air delivery6.908463 minutes
150 reference L/minConstant free-air delivery4.605642 minutes
200 reference L/minConstant free-air delivery3.454231 minutes
300 reference L/minConstant free-air delivery2.302821 minutes

Unchanged inputs use: Receiver internal volume = 100 L; Starting absolute pressure = 100 kPa abs; Final absolute pressure = 800 kPa abs; Free-air reference pressure = 101.325 kPa abs; Constant free-air delivery = 100 reference L/min. Results retain the model limitations described above.

Common questions

Can I use a compressor displacement rating?

Only if it is a justified delivered reference-volume rate for this calculation; geometric displacement and free-air delivery differ.

Does the reference pressure need to be absolute?

Yes. The storage increment uses a pressure difference, while reference pressure is absolute.

Does this infer CFM from motor horsepower?

No. It requires the delivery rate as an input.

What if final pressure is below initial pressure?

That is not a positive receiver-filling interval and is rejected.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NASA Glenn: conservation of mass, ideal gas and compressible nozzle flowhttps://www.grc.nasa.gov/www/k-12/airplane/mflchk.html
  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9