Flow rate calculators / Flow unit conversions
Measure flow. Understand the conditions.
Volumetric Flow Unit Converter
Convert compatible volume rates across metric, US, Imperial, cubic-foot and petroleum-barrel units.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Output = input × SI volume/time factor for input unit / SI volume/time factor for output unit.
Convert compatible volume rates across metric, US, Imperial, cubic-foot and petroleum-barrel units.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Geometric volume/time conversion only; no mass-density or gas-state correction.
Volumetric Flow Unit Converter: inputs and interpretation
This selector covers combinations beyond the focused pair pages, including CFM-to-GPM geometric equivalents. Such a numeric equivalence does not turn an air-flow device into a liquid-flow device or correct gas reference conditions. Gallon and barrel labels explicitly identify their conventions.
Use compatible units and verify the measurement basis before interpreting a result.
Continue with: US GPM to US GPH Converter · US GPH to L/h Converter · US GPM to L/min Converter · US GPM to L/s Converter
Check the numbers
Volumetric Flow Unit Converter: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Volume-rate value = 1 ; From volume-rate unit = US GPM; To volume-rate unit = L/min.
| Output | Computed result |
|---|---|
| Geometric volume-rate conversion | 3.785412 L/min |
| Applied multiplier | 3.785412 ratio |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.25 | Volume-rate value | 0.946353 L/min |
| 0.5 | Volume-rate value | 1.892706 L/min |
| 0.75 | Volume-rate value | 2.839059 L/min |
| 1 | Volume-rate value | 3.785412 L/min |
| 1.5 | Volume-rate value | 5.678118 L/min |
| 2 | Volume-rate value | 7.570824 L/min |
| 3 | Volume-rate value | 11.356235 L/min |
Unchanged inputs use: Volume-rate value = 1 ; From volume-rate unit = US GPM; To volume-rate unit = L/min. Results retain the model limitations described above.
Common questions
Can I convert CFM to GPM?
Geometric volume/time units can be rescaled at a matching state. That does not establish equivalent fluid behavior or equipment capacity.
Does the converter assume US or Imperial gallons?
They are separate labeled choices; do not treat an unspecified GPM figure as unambiguous.
Are mL/min and cm³/min equal?
Yes as geometric units, because one millilitre is one cubic centimetre.
Can SCFM or Nm³/h be entered as actual volume flow?
Only after confirming matching state definitions or performing the appropriate reference-condition correction.
Is CMH the same as m³/h, and is CMM m³/min?
Those abbreviations commonly mean cubic metres per hour and cubic metres per minute. Confirm the source notation. Select m³/h or m³/min explicitly; m³ without a time denominator is a total volume.
Can I convert cc to LPM or cm³ to GPM?
A cubic centimetre or cc is a volume, so a time basis is missing. A specified cc/min equals mL/min and can be converted. A pump displacement in cc/rev additionally needs speed and volumetric efficiency.
What does BWPD mean in a GPM conversion?
It commonly denotes barrels of water per day in petroleum use. If that is the source convention, select petroleum bbl/day, where one barrel is 42 US gallons. Do not assume the same barrel for other industries.
Does a CFM conversion chart apply to SCFM?
Only after confirming the same reference state. The geometric factors in these tables do not correct pressure, temperature, compressibility or moisture. Use the separate actual/standard gas tools when states differ.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9