Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Flow unit conversions

Measure flow. Understand the conditions.

US GPM to Imperial GPM Converter

Convert US GPM and Imperial GPM in either direction with explicit volume or mass and time conventions.

Your flow inputs

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Forward result = input × (6.30901964e-05/7.5768166666667e-05); reverse uses the reciprocal.

Convert US GPM and Imperial GPM in either direction with explicit volume or mass and time conventions.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This converts geometric volume/time units at a matching state; it does not correct gas reference pressure, temperature, density or wet/dry basis.

US GPM to Imperial GPM Converter: inputs and interpretation

US and Imperial gallons are different volumes even though both may be abbreviated GPM. The input unit is defined here as US liquid gallons per minute; one US liquid gallon is 3.785411784 litres. The other unit is Imperial gallons per minute; one Imperial gallon is 4.54609 litres. These definitions prevent an ambiguous abbreviation from silently changing the physical amount.

Use compatible units and verify the measurement basis before interpreting a result.

Check the numbers

US GPM to Imperial GPM Converter: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Flow value = 1 ; Conversion direction = US GPM to Imperial GPM.

OutputComputed result
Same-basis unit conversion0.832674 Imperial GPM
Applied multiplier0.832674 ratio
Dimension basisvolume

How one input changes the answer

ScenarioChanged inputResult
0.25 Flow value0.208169 Imperial GPM
0.5 Flow value0.416337 Imperial GPM
0.75 Flow value0.624506 Imperial GPM
1 Flow value0.832674 Imperial GPM
1.5 Flow value1.249011 Imperial GPM
2 Flow value1.665348 Imperial GPM
3 Flow value2.498023 Imperial GPM

Unchanged inputs use: Flow value = 1 ; Conversion direction = US GPM to Imperial GPM. Results retain the model limitations described above.

Common questions

How do I convert US GPM to Imperial GPM?

Multiply by 0.832674184629. The reverse direction divides by that same factor; the selector performs both directions.

What is 1 US GPM in Imperial GPM?

Using the explicitly defined units, 1 US GPM is 0.832674184629 Imperial GPM. Displayed decimals are rounded; the calculation retains the underlying unit factors.

Does the numeric conversion establish a device capacity?

No. It expresses a supplied rate in different units and does not determine pump, pipe, fan, meter or treatment suitability.

Do I need density for this conversion?

Not for this same-dimension conversion. Crossing between a mass rate and a volume rate would require an appropriate density.

Can I use an unspecified gallon, barrel or gas standard?

No. Confirm the exact gallon/barrel convention and, for gas volumes, matching reference conditions. The unit labels here are explicit.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9