Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Flow unit conversions

Measure flow. Understand the conditions.

US GPD to US GPM Converter

Convert US GPD and US GPM in either direction with explicit volume or mass and time conventions.

Your flow inputs

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Forward result = input × (4.3812636388889e-08/6.30901964e-05); reverse uses the reciprocal.

Convert US GPD and US GPM in either direction with explicit volume or mass and time conventions.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This converts geometric volume/time units at a matching state; it does not correct gas reference pressure, temperature, density or wet/dry basis.

US GPD to US GPM Converter: inputs and interpretation

A daily total rate and a minute-based average refer to different time scales; this conversion assumes a matching representative rate. The input unit is defined here as US liquid gallons per day. The other unit is US liquid gallons per minute; one US liquid gallon is 3.785411784 litres. These definitions prevent an ambiguous abbreviation from silently changing the physical amount.

Use compatible units and verify the measurement basis before interpreting a result.

Check the numbers

US GPD to US GPM Converter: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Flow value = 1 ; Conversion direction = US GPD to US GPM.

OutputComputed result
Same-basis unit conversion0.000694 US GPM
Applied multiplier0.000694 ratio
Dimension basisvolume

How one input changes the answer

ScenarioChanged inputResult
0.25 Flow value0.000174 US GPM
0.5 Flow value0.000347 US GPM
0.75 Flow value0.000521 US GPM
1 Flow value0.000694 US GPM
1.5 Flow value0.001042 US GPM
2 Flow value0.001389 US GPM
3 Flow value0.002083 US GPM

Unchanged inputs use: Flow value = 1 ; Conversion direction = US GPD to US GPM. Results retain the model limitations described above.

Common questions

How do I convert US GPD to US GPM?

Multiply by 0.000694444444444. The reverse direction divides by that same factor; the selector performs both directions.

What is 1 US GPD in US GPM?

Using the explicitly defined units, 1 US GPD is 0.000694444444444 US GPM. Displayed decimals are rounded; the calculation retains the underlying unit factors.

Does the numeric conversion establish a device capacity?

No. It expresses a supplied rate in different units and does not determine pump, pipe, fan, meter or treatment suitability.

Do I need density for this conversion?

Not for this same-dimension conversion. Crossing between a mass rate and a volume rate would require an appropriate density.

Can I use an unspecified gallon, barrel or gas standard?

No. Confirm the exact gallon/barrel convention and, for gas volumes, matching reference conditions. The unit labels here are explicit.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9