Flow Rate CalculatorLiquid, gas & engineering tools

Flow rate calculators / Valves & flow measurement

Measure flow. Understand the conditions.

Valve Kv Flow Calculator

Calculate the simple metric Kv liquid-flow relationship with explicit pressure and density basis.

Your flow inputs

metric basis
bar
water-relative

Starting values are illustrative. Check units and assumptions below. Calculate submits your inputs to this site’s result page.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Liquid flow m³/h = Kv × √(pressure drop bar / specific gravity).

Calculate the simple metric Kv liquid-flow relationship with explicit pressure and density basis.

  1. Choose a measurement plane and use compatible units for all inputs.
  2. Obtain appropriate product data or representative measurements for the stated model.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is not a complete control-valve manufacturer sizing implementation.

Valve Kv Flow calculation: inputs and interpretation

Use Kv rather than a numerically identical Cv. Converting reference units gives approximately Kv = 0.865×Cv; a rounded conversion should not be mistaken for an exact calibration. The displayed flow remains subject to the simplified liquid assumptions.

Discharge and valve coefficients describe a specific device and test basis. The examples are not certified calibrations. Pressure-tap arrangement, density, Reynolds number and downstream conditions can change the relationship between a measured pressure difference and actual flow.

Check the numbers

Valve Kv Flow Calculator: calculated examples

These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.

Worked example with stated inputs

Valve flow coefficient Kv = 5 metric basis; Valve pressure difference = 1 bar; Liquid specific gravity = 1 water-relative.

OutputComputed result
Simple metric Kv liquid flow5 m³/h
Volume flow SI0.001389 m³/s
Volume flow hourly5 m³/h
US liquid flow22.014338 US GPM
Cubic feet per minute2.942889 CFM

How one input changes the answer

ScenarioChanged inputResult
0.25 barValve pressure difference2.5 m³/h
0.5 barValve pressure difference3.535534 m³/h
0.75 barValve pressure difference4.330127 m³/h
1 barValve pressure difference5 m³/h
1.5 barValve pressure difference6.123724 m³/h
2 barValve pressure difference7.071068 m³/h
3 barValve pressure difference8.660254 m³/h

Unchanged inputs use: Valve flow coefficient Kv = 5 metric basis; Valve pressure difference = 1 bar; Liquid specific gravity = 1 water-relative. Results retain the model limitations described above.

Common questions

Does Kv mean flow in litres per minute?

Its conventional numerical reference is m³/h of water at the specified pressure-drop basis, not L/min.

Can I use a Cv value unchanged?

No. Convert the coefficient definition or obtain the actual Kv specification.

Does it include gas pressure-ratio corrections?

No. This page is for the simple liquid relationship only.

Can I compare valves at one pressure drop?

As a preliminary coefficient comparison if their rating bases and operating conditions are compatible.

Which assumptions should I verify?

Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.

Where are the formula sources?

Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.

  • Emerson Control Valve Handbook, Chapter 5: liquid and gas sizing boundarieshttps://www.emerson.com/is/content/emerson/it/final-control/flow-controls/valves/documents/control-valve-handbook-en-3661206.pdf
  • NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9