Flow rate calculators / Open channels & drainage
Measure flow. Understand the conditions.
Confined Aquifer Radial Flow Calculator
Apply a simplified Thiem confined-aquifer relationship to two observation radii.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Steady confined-flow magnitude Q = 2π × conductivity × thickness × head difference / ln(outer radius/inner radius).
Apply a simplified Thiem confined-aquifer relationship to two observation radii.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
Not a sustainable-yield approval or interpretation of an arbitrary transient well test.
Confined Aquifer Radial Flow calculation: inputs and interpretation
The model assumes steady radial flow in an ideal confined aquifer with compatible observation heads. The outer radius must exceed the inner radius. Actual pumping tests can require transient, boundary, leakage or partial-penetration analysis.
Uniform-flow and free-overfall formulas have operating limits. A backwater, hydraulic jump, submerged outlet or inlet-controlled culvert may require a different analysis. Roughness and discharge coefficients are explicit inputs rather than universal material guarantees.
Continue with: Rectangular Channel Flow Calculator · Trapezoidal Channel Flow Calculator · Partially Full Pipe Flow Calculator · Normal Depth Calculator
Check the numbers
Confined Aquifer Radial Flow Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Hydraulic conductivity = 0.0001 m/s; Confined aquifer thickness = 10 m; Positive head difference = 1 m; Inner observation radius = 1 m; Outer observation radius = 100 m.
| Output | Computed result |
|---|---|
| Steady confined radial flow | 0.001364 m³/s |
| Volume flow SI | 0.001364 m³/s |
| Volume flow hourly | 4.911755 m³/h |
| US liquid flow | 21.625806 US GPM |
| Cubic feet per minute | 2.89095 CFM |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 0.25 m | Positive head difference | 0.000341 m³/s |
| 0.5 m | Positive head difference | 0.000682 m³/s |
| 0.75 m | Positive head difference | 0.001023 m³/s |
| 1 m | Positive head difference | 0.001364 m³/s |
| 1.5 m | Positive head difference | 0.002047 m³/s |
| 2 m | Positive head difference | 0.002729 m³/s |
| 3 m | Positive head difference | 0.004093 m³/s |
Unchanged inputs use: Hydraulic conductivity = 0.0001 m/s; Confined aquifer thickness = 10 m; Positive head difference = 1 m; Inner observation radius = 1 m; Outer observation radius = 100 m. Results retain the model limitations described above.
Common questions
Can I use it for an unconfined aquifer?
Not directly. The unconfined relationship differs.
What does the head difference mean?
Use the appropriate positive head difference between the two stated observation locations under the model.
Can the radii be equal?
No. The logarithmic denominator would be zero.
Does this determine aquifer conductivity from one guessed flow?
No. This page computes discharge from the supplied parameters without test inversion or uncertainty analysis.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- USGS Open-File Report 90-183: Darcy flow and the Thiem confined-radial-flow derivationhttps://pubs.usgs.gov/of/1990/ofr90-183/pdf/ofr_90-183_e.pdf