Flow rate calculators / Flow fundamentals
Measure flow. Understand the conditions.
Tank Filling Time Calculator
Calculate time to add a stated volume when the net filling rate is constant and positive.
Your flow inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Fill time = required volume / (inflow − outflow).
Calculate time to add a stated volume when the net filling rate is constant and positive.
- Choose a measurement plane and use compatible units for all inputs.
- Obtain appropriate product data or representative measurements for the stated model.
- Submit the form, then interpret the result with the assumptions and limits below.
An inflow no greater than outflow cannot achieve the requested positive filling under this model.
Tank Filling Time calculation: inputs and interpretation
Account for simultaneous use or discharge instead of dividing by inlet flow alone. The required volume is the amount to add, not necessarily the tank’s full geometric capacity. This model assumes the flow rates stay constant as level and system pressure change.
Keep the same time basis when comparing readings. A volume total, an average rate and an instantaneous meter value answer different questions. Use the actual wetted section or measured fluid quantity rather than an outside pipe dimension or an equipment nameplate that does not describe the operating condition.
Continue with: Flow Rate Calculator · Pipe Flow Rate Calculator · Flow Velocity Calculator · Pipe Diameter from Flow Calculator
Check the numbers
Tank Filling Time Calculator: calculated examples
These are computed scenarios using the same server calculation as the form. They are not manufacturer ratings or prescribed design values.
Worked example with stated inputs
Volume to add = 1000 L; Constant inflow = 60 L/min; Simultaneous constant outflow = 0 L/min.
| Output | Computed result |
|---|---|
| Constant-net-flow fill time | 16.666667 minutes |
| Same duration | 0.277778 hours |
| Net filling rate | 60 L/min |
How one input changes the answer
| Scenario | Changed input | Result |
|---|---|---|
| 250 L | Volume to add | 4.166667 minutes |
| 500 L | Volume to add | 8.333333 minutes |
| 750 L | Volume to add | 12.5 minutes |
| 1000 L | Volume to add | 16.666667 minutes |
| 1500 L | Volume to add | 25 minutes |
| 2000 L | Volume to add | 33.333333 minutes |
| 3000 L | Volume to add | 50 minutes |
Unchanged inputs use: Volume to add = 1000 L; Constant inflow = 60 L/min; Simultaneous constant outflow = 0 L/min. Results retain the model limitations described above.
Common questions
Does this model a pump curve changing with tank level?
No. Enter a justified constant net rate or use a more detailed transient model.
Can I calculate pool filling time?
Yes for a known volume and representative constant inlet/outlet rates.
What if inflow equals outflow?
There is no positive net filling rate and no finite fill time for a positive target volume.
Does it allow for overflow capacity?
No. It calculates volume/time and does not design overflow or level protection.
Can I convert GPM to volume?
A duration is also required: collected volume equals constant flow times elapsed time. This form instead solves for the time required to reach a stated volume at a constant net flow. Changing or interrupted flow requires integration or a representative average.
Which assumptions should I verify?
Check every unit, the observation period and the physical or reference-state boundary stated above. Starting inputs and computed examples are illustrative scenarios, not recommended settings, certified capacities or universal standards.
Where are the formula sources?
Published method and unit references appear at the bottom of this page as plain-text addresses. Computed tables use the same server calculation as the form. No external content-data file is needed at runtime.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, current tariffs or proprietary test results.
- US Bureau of Reclamation Water Measurement Manual, 2.4: discharge, area and velocityhttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_04.html
- NIST SP 811 Appendix B.9: volume, mass and flow unit factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9